-
1 fréquence interharmonique
интергармоническая частота
Любая частота, не кратная основной частоте.По аналогии с порядком кратности гармоник порядок интергармонической частоты основан на отношении к основной частоте. Если это отношение меньше единицы, то такую гармоническую частоту называют субгармонической. В соответствии с рекомендацией МЭК порядок интергармонических частот обозначается буквой «m»
EN
interharmonic frequency
frequency which is a non-integer multiple of the reference fundamental frequency
NOTE 1 By extension of the harmonic order, the interharmonic order is the ratio of interharmonic frequency to the reference fundamental frequency, this ratio is not an integer (recommended notation " m ").
NOTE 2 In the case where " m 1" the term of sub-harmonic frequency may also be used (see IEV 551-20-10).
[IEC 60146-1-1, ed. 4.0 (2009-06)]FR
fréquence interharmonique
fréquence qui est un multiple non entier de la fréquence fondamentale de référence
NOTE 1 Par extension du rang harmonique, le rang interharmonique désigne le rapport de la fréquence interharmonique à la fréquence fondamentale de référence. Ce rapport n’est pas un entier (notation recommandée « m »).
NOTE 2 Lorsque « m < 1 », le terme de fréquence sous-harmonique peut également être employé (voir VEI 551-20-10).
[IEC 60146-1-1, ed. 4.0 (2009-06)]Тематики
EN
FR
частота интергармоники
Частота, которая не является целым кратным основной частоте.
Примечания.
1. Аналогично понятию "порядок гармоники" под " порядком интергармоники" понимают отношение частоты интергармоники к основной частоте. Это отношение не выражается целым числом (рекомендуемое условное обозначение m).
2. Если m < 1, допускается применение термина "субгармоническая частота".
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
interharmonic frequency
any frequency which is not an integer multiple of the fundamental frequency
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
fréquence interharmonique
toute fréquence qui n’est pas un multiple entier de la fréquence fondamentale
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
EN
FR
Франко-русский словарь нормативно-технической терминологии > fréquence interharmonique
-
2 fréquence fondamentale
основная частота
первая гармоника
Низшая собственная частота колебательной системы.
Единица измерения
Гц
[Система неразрушающего контроля. Виды (методы) и технология неразрушающего контроля. Термины и определения (справочное пособие). Москва 2003 г.]
основная частота
Частота в спектре, полученном путем преобразования Фурье функции времени, относительно которой рассматриваются все частоты спектра.
В случае возможного риска неопределенности при определении основной частоты данная частота должна быть определена с учетом числа полюсов и скорости вращения синхронного генератора (генераторов), питающего систему электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
fundamental frequency
frequency in the spectrum obtained from a Fourier transform of a time function, to which all the frequencies of the spectrum are referred
NOTE In case of any remaining risk of ambiguity, the fundamental frequency may be derived from the number of poles and speed of rotation of the synchronous generator(s) feeding the system
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
fréquence fondamentale
fréquence du spectre obtenue à partir d’une transformée de Fourier d’une fonction temporelle, servant de référence à toutes les autres fréquences du spectre
NOTE S’il subsiste un risque d’ambiguïté, la fréquence fondamentale peut être déterminée à partir du nombre de pôles et de la vitesse de rotation du ou des générateurs synchrones alimentant le réseau.
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- виды (методы) и технология неразр. контроля
- качество электрической энергии
Синонимы
EN
FR
Франко-русский словарь нормативно-технической терминологии > fréquence fondamentale
-
3 fréquence harmonique
частота гармоники
Частота, кратная основной частоте.
Примечание. Отношение частоты гармоники к основной частоте называют "порядком гармоники".
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
harmonic frequency
frequency which is an integer multiple of the fundamental frequency
NOTE The ratio of the harmonic frequency to the fundamental frequency is the harmonic order (notation: h).
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
fréquence harmonique
fréquence qui est un multiple entier de la fréquence fondamentale
NOTE Le rapport entre la fréquence harmonique et la fréquence fondamentale est le rang harmonique (notation: h).
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
EN
FR
Франко-русский словарь нормативно-технической терминологии > fréquence harmonique
-
4 composante fondamentale
основная составляющая
Составляющая первого порядка ряда Фурье периодической величины.
[ ГОСТ Р 51317.4.13-2006]
основная составляющая
Составляющая напряжения, частота которой равна основной частоте.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
fundamental component
component whose frequency is the fundamental frequency
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
composante fondamentale
composante dont la fréquence est la fréquence fondamentale
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
EN
FR
Франко-русский словарь нормативно-технической терминологии > composante fondamentale
-
5 régulateur régulateur
контроллер компенсации реактивной мощности
-
[Интент]EN
automatic reactive power regulator, controller
circuit designed to calculate the reactive power absorbed by the load connected to the power line and to control the switching on and off of the steps of the automatic bank, in order to compensate for the reactive power
NOTE 1 The reactive power is normally calculated at the fundamental frequency.
NOTE 2 The controller may be “built-in” or “free-standing” and has usually to be adjusted for each bank before operation.
[IEC 61921, ed. 1.0 (2003-04)]FR
régulateur varmétrique, régulateur
circuit conçu pour calculer la puissance réactive absorbée par la charge raccordée à l’alimentation de puissance et pour commander la connexion et la déconnexion des gradins de la batterie automatique de façon à compenser la puissance réactive
NOTE 1 La puissance réactive est normalement calculée à la fréquence fondamentale.
NOTE 2 Le régulateur peut être incorporé ou séparé et est normalement paramétré en fonction de la batterie avant fonctionnement.
[IEC 61921, ed. 1.0 (2003-04)]Тематики
Синонимы
EN
- automatic reactive power controller
- automatic reactive power regulator
- power factor controller
- reactive power controller
FR
Франко-русский словарь нормативно-технической терминологии > régulateur régulateur
-
6 régulateur varmétrique
контроллер компенсации реактивной мощности
-
[Интент]EN
automatic reactive power regulator, controller
circuit designed to calculate the reactive power absorbed by the load connected to the power line and to control the switching on and off of the steps of the automatic bank, in order to compensate for the reactive power
NOTE 1 The reactive power is normally calculated at the fundamental frequency.
NOTE 2 The controller may be “built-in” or “free-standing” and has usually to be adjusted for each bank before operation.
[IEC 61921, ed. 1.0 (2003-04)]FR
régulateur varmétrique, régulateur
circuit conçu pour calculer la puissance réactive absorbée par la charge raccordée à l’alimentation de puissance et pour commander la connexion et la déconnexion des gradins de la batterie automatique de façon à compenser la puissance réactive
NOTE 1 La puissance réactive est normalement calculée à la fréquence fondamentale.
NOTE 2 Le régulateur peut être incorporé ou séparé et est normalement paramétré en fonction de la batterie avant fonctionnement.
[IEC 61921, ed. 1.0 (2003-04)]Тематики
Синонимы
EN
- automatic reactive power controller
- automatic reactive power regulator
- power factor controller
- reactive power controller
FR
Франко-русский словарь нормативно-технической терминологии > régulateur varmétrique
-
7 tension assignée
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
Франко-русский словарь нормативно-технической терминологии > tension assignée
-
8 tension nominale
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
номинальное напряжение конденсатора
Максимальное напряжение, при котором конденсатор может работать в течение минимальной наработки в условиях, указанных в нормативно-технической документации
[ ГОСТ 21415-75]
номинальное напряжение конденсатора
Действующее значение синусоидального переменного напряжения при номинальной частоте, на которое рассчитан конденсатор. Номинальное напряжение многофазного конденсатора - значение напряжения между выводами.
[ ГОСТ 1282-88]Тематики
- конденсаторы для повыш. коэф. мощности
- конденсаторы для электронной аппаратуры
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > tension nominale
-
9 Un
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
Франко-русский словарь нормативно-технической терминологии > Un
-
10 oscillateur
осциллятор
-
[IEV number 151-13-51]EN
oscillator
active device for producing a periodic quantity the fundamental frequency of which is deter-mined by the characteristics of the device
Source: 702-09-22 MOD
[IEV number 151-13-51]FR
oscillateur, m
dispositif actif destiné à produire une grandeur périodique dont la fréquence fondamentale est déterminée par les caractéristiques du dispositif
Source: 702-09-22 MOD
[IEV number 151-13-51]EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > oscillateur
-
11 composante interharmonique
интергармоника
Интергармониками называют токи (напряжения) частота которых не кратна частоте основной гармоники.EN
interharmonic component
sinusoidal component of a periodic quantity having a an interharmonic frequency
NOTE 1 For brevity, such a component may be referred to simply as an interharmonic.
NOTE 2 For practical analysis, an approximation of the periodicity may be necessary.
NOTE 3 The value is normally expressed as an r.m.s. value.
NOTE 4 As stated in IEC 61000-4-7, the time window has a width of 10 fundamental periods (50 Hz systems) or 12 fundamental periods (60 Hz systems), i.e. approximately 200 ms. The difference in frequency between two consecutive interharmonic components is, therefore, approximately 5 Hz. In the case of other fundamental frequencies, the time window should be selected between 6 fundamental periods (approximately 1 000 ms at 6 Hz) and 18 fundamental periods (approximately 100 ms at 180 Hz).
[IEC 60146-1-1, ed. 4.0 (2009-06)]FR
composante interharmonique
composante sinusoïdale d’une grandeur périodique dont la fréquence est une fréquence interharmonique
NOTE 1 Pour des raisons de concision, ce type de composante peut être désigné simplement par le terme « interharmonique ».
NOTE 2 Pour l’analyse pratique, il peut être nécessaire de procéder à une approximation de la périodicité.
NOTE 3 La valeur est normalement exprimée comme une valeur efficace.
NOTE 4 Comme indiqué dans la CEI 61000-4-7, la fenêtre temporelle a une largeur de 10 périodes fondamentales (systèmes de 50 Hz) ou de 12 périodes fondamentales (systèmes de 60 Hz), c’est-à-dire approximativement 200 ms. La différence de fréquence entre deux composantes interharmoniques consécutives est, par conséquent, d’environ 5 Hz. Dans le cas d’autres fréquences fondamentales, il convient de choisir la fenêtre temporelle entre 6 périodes fondamentales (environ 1 000 ms à 6 Hz) et 18 périodes fondamentales (environ 100 ms à 180 Hz). [IEC 60146-1-1, ed. 4.0 (2009-06)]
На частотах, расположенных между частотами гармонических составляющих тока и напряжения, могут наблюдаться интергармоники. Интергармоники могут возникать на дискретных частотах или иметь спектральные составляющие в достаточно широкой полосе частот. Суммарное воздействие различных источников интергармоник маловероятно и в настоящем стандарте не учитывается.
Полного понимания природы электромагнитных возмущений, ассоциирующихся с интергармониками, еще нет, и в настоящее время к этому явлению возник повышенный интерес. Интергармоники всегда присутствуют в системе электроснабжения, но в последнее время с резким увеличением силовых электронных систем их практическое влияние стало более ощутимым.
[Збигнев Ханзелка (Zbigniew Hanzelka), Анжей Бьень (Andrzej Bien) AGH-UST, Краков, Республика Польша. Энергосбережение №7/2005]Тематики
Действия
Синонимы
EN
FR
интергармоническая составляющая
Составляющая на частоте интергармоники.
Значение интергармонической составляющей обычно выражается среднеквадратическим значением. Для краткости вместо термина "интергармоническая составляющая" допускается применение термина "интергармоника".
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
interharmonic component
component having an interharmonic frequency
NOTE Its value is normally expressed as an r.m.s. value. For brevity, such a component may be referred to simply as an interharmonic.
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
composante interharmonique
composante ayant une fréquence interharmonique
NOTE Sa valeur est en général exprimée sous la forme d’une valeur efficace. Pour des raisons de concision, cette composante peut être simplement appelée interharmonique
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
Синонимы
EN
FR
Франко-русский словарь нормативно-технической терминологии > composante interharmonique
-
12 interharmonique
интергармоника
Интергармониками называют токи (напряжения) частота которых не кратна частоте основной гармоники.EN
interharmonic component
sinusoidal component of a periodic quantity having a an interharmonic frequency
NOTE 1 For brevity, such a component may be referred to simply as an interharmonic.
NOTE 2 For practical analysis, an approximation of the periodicity may be necessary.
NOTE 3 The value is normally expressed as an r.m.s. value.
NOTE 4 As stated in IEC 61000-4-7, the time window has a width of 10 fundamental periods (50 Hz systems) or 12 fundamental periods (60 Hz systems), i.e. approximately 200 ms. The difference in frequency between two consecutive interharmonic components is, therefore, approximately 5 Hz. In the case of other fundamental frequencies, the time window should be selected between 6 fundamental periods (approximately 1 000 ms at 6 Hz) and 18 fundamental periods (approximately 100 ms at 180 Hz).
[IEC 60146-1-1, ed. 4.0 (2009-06)]FR
composante interharmonique
composante sinusoïdale d’une grandeur périodique dont la fréquence est une fréquence interharmonique
NOTE 1 Pour des raisons de concision, ce type de composante peut être désigné simplement par le terme « interharmonique ».
NOTE 2 Pour l’analyse pratique, il peut être nécessaire de procéder à une approximation de la périodicité.
NOTE 3 La valeur est normalement exprimée comme une valeur efficace.
NOTE 4 Comme indiqué dans la CEI 61000-4-7, la fenêtre temporelle a une largeur de 10 périodes fondamentales (systèmes de 50 Hz) ou de 12 périodes fondamentales (systèmes de 60 Hz), c’est-à-dire approximativement 200 ms. La différence de fréquence entre deux composantes interharmoniques consécutives est, par conséquent, d’environ 5 Hz. Dans le cas d’autres fréquences fondamentales, il convient de choisir la fenêtre temporelle entre 6 périodes fondamentales (environ 1 000 ms à 6 Hz) et 18 périodes fondamentales (environ 100 ms à 180 Hz). [IEC 60146-1-1, ed. 4.0 (2009-06)]
На частотах, расположенных между частотами гармонических составляющих тока и напряжения, могут наблюдаться интергармоники. Интергармоники могут возникать на дискретных частотах или иметь спектральные составляющие в достаточно широкой полосе частот. Суммарное воздействие различных источников интергармоник маловероятно и в настоящем стандарте не учитывается.
Полного понимания природы электромагнитных возмущений, ассоциирующихся с интергармониками, еще нет, и в настоящее время к этому явлению возник повышенный интерес. Интергармоники всегда присутствуют в системе электроснабжения, но в последнее время с резким увеличением силовых электронных систем их практическое влияние стало более ощутимым.
[Збигнев Ханзелка (Zbigniew Hanzelka), Анжей Бьень (Andrzej Bien) AGH-UST, Краков, Республика Польша. Энергосбережение №7/2005]Тематики
Действия
Синонимы
EN
FR
Франко-русский словарь нормативно-технической терминологии > interharmonique
-
13 réactance homopolaire
реактивное сопротивление нулевой последовательности
-EN
zero sequence reactance
the quotient of the reactive fundamental component of zero sequence armature voltage, due to the presence of fundamental zero sequence armature current at rated frequency, by the value of that component of current, the machine running at rated speed
[IEV ref 411-50-16]FR
réactance homopolaire
quotient du terme fondamental de la composante réactive de la tension d'induit homopolaire, due à la présence du terme fondamental du courant d'induit homopolaire à fréquence assignée, par cette composante du courant, la machine tournant à sa vitesse assignée
[IEV ref 411-50-16]Тематики
- электротехника, основные понятия
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > réactance homopolaire
-
14 impédance du circuit d'entrée
входное полное сопротивление
-
[IEV number 312-06-18]EN
input impedance
impedance of the input circuit measured between the input terminals under operating conditions
NOTE 1 – The impedance can be expressed in terms of admittance.
NOTE 2 – In certain instances, for example, sampling devices or self-balancing potentiometers, the impedance can be different according to the instant when it is determined, before, during or after the instant of measurement.
NOTE 3 – When the input circuit is such that the instantaneous value of the current flowing into the input terminals is a non-linear function of the instantaneous value of the input voltage under specified conditions of frequency and voltage, the combination of resistance and reactance which would absorb the same active power and in which would flow a reactive current equal to the fundamental component that is flowing in the actual input circuit, is sometimes called the "equivalent input impedance".
[IEV number 312-06-18]FR
impédance du circuit d'entrée
impédance du circuit d'entrée entre les bornes d'entrée dans les conditions de fonctionnement
NOTE 1 – L'impédance peut être exprimée en termes d'admittance.
NOTE 2 – Dans certains cas, par exemple les dispositifs d'échantillonnage ou les potentiomètres à rééquilibrage automatique, l'impédance peut être différente selon l’instant où elle est déterminée, avant, pendant ou après la mesure.
NOTE 3 – Lorsque le circuit d'entrée est tel que la valeur instantanée du courant traversant les bornes d'entrée est une fonction non linéaire de la valeur instantanée de la tension d'entrée dans des conditions spécifiées de fréquence et de tension, l'impédance d'une combinaison formée par une résistance et une réactance qui absorberaient la même puissance active et dans laquelle circulerait un courant réactif égal à la composante fondamentale qui circule dans le circuit d'entrée réel, est parfois appelée "impédance équivalente d'entrée".
[IEV number 312-06-18]Тематики
- измерение электр. величин в целом
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > impédance du circuit d'entrée
-
15 impédance du circuit de sortie
выходное полное сопротивление
-
[IEV number 312-06-19]EN
output impedance
impedance of the output circuit measured between the output terminals under operating conditions
NOTE 1 – The impedance can be expressed in terms of admittance.
NOTE 2 – In certain instances, for example, sampling devices or self-balancing potentiometers, the impedance can be different according to the instant when it is determined, before, during or after the instant of measurement.
NOTE 3 – When the output circuit is such that the instantaneous value of the current flowing into the output terminals is a non-linear function of the instantaneous value of the output voltage under specified conditions of frequency and voltage, the combination of resistance and reactance which would absorb the same active power and in which would flow a reactive current equal to the fundamental component that is flowing in the actual output circuit, is sometimes called the "equivalent output impedance".
[IEV number 312-06-19]FR
impédance du circuit de sortie
impédance du circuit de sortie entre les bornes de sortie dans les conditions de fonctionnement
NOTE 1 – L'impédance peut être exprimée en termes d'admittance.
NOTE 2 – Dans certains cas, par exemple les dispositifs d'échantillonnage ou les potentiomètres à rééquilibrage automatique, l'impédance peut être différente selon l’instant où elle est déterminée, avant, pendant ou après la mesure.
NOTE 3 – Lorsque le circuit de sortie est tel que la valeur instantanée du courant traversant les bornes de sortie est une fonction non linéaire de la valeur instantanée de la tension de sortie dans des conditions spécifiées de fréquence et de tension, l'impédance d'une combinaison formée par une résistance et une réactance qui absorberaient la même puissance active et dans laquelle circulerait un courant réactif égal à la composante fondamentale qui circule dans le circuit de sortie réel, est parfois appelée "impédance équivalente de sortie".
[IEV number 312-06-19]Тематики
- измерение электр. величин в целом
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > impédance du circuit de sortie
-
16 réactance inverse
реактивное сопротивление обратной последовательности
-EN
negative sequence reactance
the quotient of the reactive fundamental component of negative sequence armature voltage, due to the sinusoidal negative sequence armature current at rated frequency, by the value of that component of current, the machine running at rated speed
[IEV ref 411-50-15]FR
réactance inverse
quotient du terme fondamental de la composante réactive de la tension d'induit inverse, due à la composante inverse du courant d'induit sinusoïdal à fréquence assignée, par la valeur de ce courant, la machine tournant à sa vitesse assignée
[IEV ref 411-50-15]Тематики
- электротехника, основные понятия
EN
- negative phase-sequence reactance
- negative sequence reactance
- subtransient reactance of negative phase
DE
FR
Франко-русский словарь нормативно-технической терминологии > réactance inverse
-
17 réactance directe
реактивное сопротивление прямой последовательности
-EN
positive sequence reactance
the quotient of the reactive fundamental component of the positive sequence armature voltage, due to the sinusoidal positive sequence armature current at rated frequency, by the value of that component of current, the machine running at rated speed
[IEV ref 411-50-14]FR
réactance directe
quotient du terme fondamental de la composante réactive de la tension d'induit directe, due à la composante directe du courant d'induit sinusoïdal à fréquence assignée, par la valeur de ce courant, la machine tournant à sa vitesse assignée
[IEV ref 411-50-14]
Тематики
- электротехника, основные понятия
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > réactance directe
См. также в других словарях:
Fundamental frequency — Vibration and standing waves in a string, The fundamental and the first 6 overtones The fundamental frequency, often referred to simply as the fundamental and abbreviated f0 or F0, is defined as the lowest frequency of a periodic waveform. In… … Wikipedia
fundamental frequency — pagrindinis dažnis statusas T sritis automatika atitikmenys: angl. fundamental frequency; master frequency vok. Grundfrequenz, f; Hauptfrequenz, f rus. основная частота, f pranc. fréquence fondamentale, f … Automatikos terminų žodynas
fundamental frequency — pagrindinis dažnis statusas T sritis Standartizacija ir metrologija apibrėžtis Dažnis, atitinkantis tam tikro nesinusinio periodinio virpesio periodą. atitikmenys: angl. basic frequency; fundamental frequency vok. Fundamentalfrequenz, f;… … Penkiakalbis aiškinamasis metrologijos terminų žodynas
fundamental frequency — pagrindinis dažnis statusas T sritis fizika atitikmenys: angl. basic frequency; fundamental frequency vok. Fundamentalfrequenz, f; Grundfrequenz, f rus. основная частота, f pranc. fréquence fondamentale, f; fréquence principale, f … Fizikos terminų žodynas
fundamental frequency — Physics. 1. the lowest frequency at which a medium will freely oscillate. 2. the frequency of the fundamental. [‡1960 65] * * * … Universalium
fundamental frequency — noun 1》 Physics the lowest frequency produced by the oscillation of the whole of an object, as distinct from harmonics. 2》 Music the principal frequency in a harmonic series … English new terms dictionary
fundamental frequency — noun the lowest tone of a harmonic series • Syn: ↑fundamental, ↑first harmonic • Hypernyms: ↑harmonic … Useful english dictionary
fundamental frequency — F/A/V the lowest frequency in a harmonic series; known as pure tone … Audio and video glossary
fundamental frequency — /ˌfʌndəmɛntl ˈfrikwənsi/ (say .funduhmentl freekwuhnsee) noun the component of lowest frequency in a complex waveform, as in sound …
suppression of fundamental frequency — pagrindinio dažnio malšinimas statusas T sritis fizika atitikmenys: angl. suppression of fundamental frequency vok. Trägerfrequenzunterdrückung, f rus. подавление основной частоты, n pranc. suppression de la fréquence fondamentale, f … Fizikos terminų žodynas
Fundamental — may refer to: * Fundamental frequency,a concept in music or phonetics, often referred to as simply a fundamental . * Fundamentalism, the belief in, and usually the strict adherence to, the simplistic or fundamental ideas based on faith of a… … Wikipedia